... Publishing Limited Licensed re-use rights only Pile foundations Thermal stress Thermo-mechanical coupling Numerical analysis Spatiotemporal evolution the Fundamental Research Funds for Central Public Welfare Research Institutes CKSF 20241003/CL the Fundamental Research Funds...

... 16 12 2024 04 01 2025 © Emerald Publishing Limited 2025 Emerald Publishing Limited Licensed re-use rights only Hybrid composites Buckling Numerical analysis DQ methods Plate theories Nowadays, traditional, auxetic, and composite materials are frequently used...

... d_f is usually determined by the following empirical equation (Barton et al., 1985). Fracture flow Permeability Representative elementary volume Columnar jointed rock masses (CJRMs) Numerical analysis Fundamental Research Funds for the Central Universities 10.13039...

... 2020 17 09 2020 © Emerald Publishing Limited 2020 Emerald Publishing Limited Licensed re-use rights only Numerical analysis Coupled burgers’ equation Quartic trigonometric tension B-splines (6) u ( x , 0 ) = f ( x ) with v 1 = r ( h 2...

... 09 2018 17 05 2019 17 05 2019 © Emerald Publishing Limited 2019 Emerald Publishing Limited Licensed re-use rights only Numerical analysis Consolidation Large deformation Cone penetration test (CPT) Footing Particle finite element method An alternative option...

... behaviors of PVD-improved ground considering a varied discharge capacity of PVD. Design/methodology/approach A simple equivalent vertical hydraulic conductivity (k′_ve method) was proposed in plane strain numerical analysis, in which the effect of decreased discharge capacity...

... equations and dimensionless time, numerical analysis was used to observe changes in the system caused by differences in excitation frequency. Design/methodology/approach To suppress this effect and improve performance, proportional differential (PD) control was used. The integral absolute error was used...

... environment was developed and stabilized. The generated thrust and lift for motion using flapping abilities were obtained. Doncieux (2009) uses evolutionary algorithms as optimization tools. This ability helps to propose a controller for a flapping wings aircraft. Numerical analysis of flapping wing...

... this issue. Design/methodology/approach – In consideration of the difficulties in observing particle velocities of high-velocity flows, this work presented a study to reveal the regularity during a methane-air explosion happening in the tunnel of coal mine through the numerical analysis approach...

... iteration Simulation Numerical analysis Sheet metal forming processes generally experience very complicated deformation effected by several process parameters such as the die geometry, the blank shape, the sheet thickness, the blank holding force, friction, lubrication and so on (Lee and Huh, 1998...

... is: Equation 9 while for the diagonal elements is: Equation 10 © Emerald Group Publishing Limited 2011 Truss‐like discrete element method Damage mechanics Fracture mechanics Stress intensity factors Elastoplastic analysis Numerical analysis During the 1960s an alternative set...

... discontinuous problems to be overcome. Thus, the difficulty of pre‐processing is transferred into a computation problem. Rocks Mechanical behaviour of materials Numerical analysis Simulation One element contains one fault segment (Figure 2(a)) and two interfaces are included in the element...

... assessment Numerical analysis © Emerald Group Publishing Limited 2010 Hua‐Peng Chen can be contacted at: h.chen@greenwich.ac.uk The framed building model, as described in the study by Johnson et al. (2004) and shown in Figure 1 , is utilised to demonstrate the applicability...

... dynamics in particular its non‐linearity by using the three‐dimensional (3D) direct numerical simulations (DNS). Flow Tracking Numerical analysis © Emerald Group Publishing Limited 2010 S.C. Li can be contacted at: S.Li@warwick.ac.uk From Equation (2), we have the discrete...

... conditions on actuator performance. Design/methodology/approach The numerical analysis is based on an existing three‐dimensional model, where the original rate‐independent evolution equations are replaced by their rate‐dependent counterparts to facilitate implementation, which is performed in a partial...

...) in such plane. The axis of principal stresses σ_{2_B1} forms a δ₁ angle with axis Y₁. Furthermore, this figure also shows radial displacement u_{r_B1} along any radius forming a β angle with reference axis Y₁. Civil engineering Mining Numerical analysis...

... can be contacted at: kinde@ing.uc3m.es Differential equations Numerical analysis Boundary‐elements methods Standard numerical methods (finite element, boundary element, finite difference, spectral methods) are very efficient in solving elliptic partial differential equations, except...

...M.Q. Al‐Odat Purpose The purpose of this paper is to conduct a full three‐dimensional numerical analysis to simulate the thermal behavior of high speed steel (HSS) cutting tool, with temperature dependent thermal properties, in dry machining with embedded heat pipe (HP), and investigate...

... software Programming Physical properties of materials Simulation Numerical analysis Granular materials are found much in nature and in various industries. For example, they are found in landslides and avalanches, raw minerals extraction and transport, cereal storage, powder mixing, without...

... method. We study here how to compute the numerical solution in a typical window for t∈[T_n,T_n+1]. Numerical analysis Mechanics Thermal stability The stability criterion calculated in the previous section is herein...