...Basavaraj Mallappa Ganiger; Chandrashekharaiah Tumbigeri Mata; H R Manohara; T B Prasad Purpose – The main purpose of the research paper is to study the effect of refinement of primary silicon on sliding wear behavior of commercially available LM-28 alloy and correlate these with the micro...

...Adalet Zeren Purpose – The purpose of this paper is to understand the effect of graphite content on the properties of aluminum alloy/silicon carbide/granite (Al/SiC/Gr) composites. Design/methodology/approach – Hardness and wear tests were applied to the powder metallurgical composites...

.../methodology/approach The tribological behaviour of aluminium alloy (Al‐Si10Mg) reinforced with alumina and graphite produced by liquid metallurgy is studied using pin‐on‐disc wear test apparatus under dry sliding condition. Experiments are conducted based on the plan of experiments generated through Taguchi...

...Ubeidulla F. Al‐Qawabeha; Safwan M. Al‐Qawabah Purpose The purpose of this paper is to review, analyze and present the effects of the roller burnishing process on pure aluminum alloyed by pure copper at 3%, 6% and 9% percentages. Roller burnishing is one of the effective finishing treatment...

...Anasyida Abu Seman; Abdul Razak Daud; Mariyam Jameelah Ghazali Purpose The purpose of this paper is to study the wear behaviour of eutectic and hypoeutectic Al‐Si‐Mg‐Ce alloys. Design/methodology/approach The eutectic and hypoeutectic alloys were prepared using permanent mould casting process...

... in drilling Ti6Al4V is smaller than that in drilling AISI 1045 due to its lower cutting deformation. The effects of feed rate on the drilling forces distribution are not serious. © Emerald Group Publishing Limited 2013 Water Vapour pressure Lubrication Cooling systems Titanium Alloys Green...

... is to determine friction coefficient and wear loss at CuSn10 alloy radial bearings by a new approach. In experiments, effects of bearings have been examined at dry and lubricated conditions and at different loads and velocities. Design/methodology/approach In this study, friction coefficient and wear losses...

...Safwan M. Al‐qawabah Purpose This paper seeks to investigate the effect of roller burnishing on the surface roughness and hardness of Zn−5% Al alloyed by copper at varied percentages. Design/methodology/approach Copper was added to molten Zn−5%Al cast alloy at different percentages...

...Erol Feyzullahoğlu; Nehir Şakiroğlu Purpose The purpose of this study is to develop new Al‐based bearing alloys which have better properties than classic commercial bearing materials and to analyze tribologic properties of these alloys under dry sliding conditions experimentally. Design...

... Alloys Plant products Oils Corrosion inhibitors anodic inhibitors; cathodic inhibitors; mixed inhibitors; screening inhibitors; vapor phase inhibitors; and acid/alkaline/neutral inhibitors. The aim of this review is to show detailed account of the inhibitors obtained...

...B.K. Prasad Purpose The objectives of this paper are to assess the sliding wear response of a zinc‐based alloy over a range of sliding speeds and pressures in oil‐lubricated condition with respect to a cast iron, to understand the role of different microconstituents in controlling the observed...

...Jian Fang; Yanqiu Xia; Weimin Liu Purpose The purpose of this paper is to study the tribological behavior and mechanism of water‐soluble bismuth dithiophosphate as the additive of water‐based cutting fluid in aluminum alloy tapping. Design/methodology/approach Comparable investigation has been...

... and their alloys. The purpose of this paper is to describe the development of an aluminum alloy‐aluminum oxide composite using a new combination of vortex method and pressure die casting technique and the subsequent tribological studies. Design/methodology/approach An aluminum alloy‐aluminum oxide composite...

... of coolants and lubricants has led to this study on a new green machining technology with application of water vapor as coolants and lubricants in cutting Ni‐based superalloys and titanium alloy Ti‐6Al‐4V with uncoated carbide inserts (ISO Type K10). The purpose of this paper is to show that machining...

...Mustafa Aydin; Fehim Findik Purpose The purpose of this paper is to improve the wear resistance and tribological properties of magnesium and its alloys in order to apply them to the friction components. Design/methodology/approach Wear test, microhardness measurements, X‐ray diffraction (XRD...

... experiments were carrying out on it. Finally, CPMJ was applied to the grinding of titanium alloy to verify its cooling effects. Findings With high penetrative power and water mist of −5°C, CPMJ can greatly improve heat transfer efficiency in the grinding zone. Experimental results, including heat transfer...

...Włodzimierz Ochoński Purpose The purpose of this paper is to present short characteristics of shape memory alloys (SMA) and shape memory polymers (SMP) and some examples of application of these materials in industrial sealing technology. Design/methodology/approach In this paper, short...

...Abdul Maleque; Rezaul Karim Purpose The purpose of this paper is to study the wear behavior of as‐cast (AC) and heat treated (HT) triple particle size (TPS) silicon carbide (SiC) reinforced aluminum alloy‐based metal matrix composites (SiC_p/Al‐MMC). Design/methodology/approach Al...

...Mustafa Yasar; Mustafa Demiral; Dursun Ozyurek; Mehmet Unal Purpose The paper's aim is to examine dry friction properties of the wear behaviors of the manufactured aluminum bronzes (C9500 and C95300) by using pin‐on‐disk type wear test device. Design/methodology/approach In this study, alloys...

...Abdul Maleque; Rezaul Karim Purpose The aim is to study the tribological behavior of dual particle size (DPS) and triple particle size (TPS) SiC reinforced aluminum alloy‐based metal matrix composites – MMCs (Al/SiC_p MMC). Design/methodology/approach Al‐MMCs with DPS and TPS of SiC...