... describe the specifications of the model used and the split of the training data set and the test data set. convolutional neural network deep learning dendritic microscopy microstructure neural networks Microstructures were first observed in 1863 by Henry Clifton Sorby as distinct...

... for 24 h and then dried. The membranes were cut into disks with a diameter of 47 mm. (corresponding author: yqaheem@kisr.edu.kw) 22 09 2021 11 11 2022 ICE Publishing: All rights reserved 2023 hydrogen separation microscopy mixed-matrix membrane LSCF particle...

... those based on microhardness and the EPMA. However, a deviation from the results derived from optical microscopy is observed, which is expected because the effect of the nitrogen atoms at a deeper level cannot be easily identified with an optical microscope (the change in the color of the microstructure...

... for type IV pressure vessels. Composite cylinders with eight cylindrical laminates of different stacking sequences and fiber content ratios were fabricated through the filament-winding technique. Damage characterization was carried out using the scanning electron microscopy technique for both composite...

... of different ratios of tests with coarse and fine aggregates were designed to determine the dynamic elastic modulus and mass loss of recycled aggregate concrete. A reliability analysis was carried out by using the Wiener probabilistic method; finally, the product was analyzed by scanning electron microscopy–X...

...) specimen in 3.5% sodium chloride ICE Publishing: All rights reserved 2020 coatings corrosion microscopy Lubrication is critical in moving parts that work under frictional conditions. A large portion of lubrication is provided by low-friction coatings. 1 Phosphate coating is one...

... Technology   205   5235   5239 9 ASTM   2018   B 117-18: Standard practice for operating salt spray (fog) apparatus   ASTM International   West Conshohocken, PA, USA laser cladding material characterisation microscopy Armor steels are special alloys that combine...

... alloys are attributed to their Y contents. (corresponding author: lxpsyx@126.com) 18 09 2017 11 10 2019 ICE Publishing: All rights reserved 2019 characterisation mechanical properties microscopy The demand for magnesium (Mg) alloys in industries has increased...

... conductivity and dielectric constant, compressive strength and scanning electron microscopy studies were done to characterize the geopolymer. The energy of the activation for conduction was found to increase with frequency. The results are discussed. Table 1 Chemical compositions of OPC, PFA and Alccofine...

...Xiao-ping Luo, PhD; Xin Wang, MS; Qiu-shu Li, PhD The microstructure and mechanical properties of as-cast and shear-extruded Mg-5·0Sn-1·5Y-0·1Zr alloys were investigated in detail using optical microscopy, scanning electron microscopy, X-ray diffraction and tensile tests. Results showed α...

... to hardening of the material by 1·5 times, while maintaining a high level of plasticity. 21 07 2014 17 11 2014 ICE Publishing: All rights reserved 2015 mechanical properties metals microscopy An advantage of severe plastic deformation (SPD) is that it permits the processing...

... using the expression: density material processing microhardness microscopy microstructure nanohardness plasma-activated sintering tungsten powders Figure 1 A typical force (load) plotted against displacement curve obtained from the nanoindenter machine The density...

... Publishing: All rights reserved 2013 aging alloys austenite intermetallics martensitic transfor mations materials science microscopy relaxation relaxation resistance * Corresponding author e-mail address:   mla44@mail.ru Plastic deformation is important in the process...

.... It has been suggested that these phases lead to the presence of coarse Nb-rich particles in the resultant steel, which may adversely affect the mechanical properties. In the present study, electron microscopy and differential scanning calorimetry (DSC) were used to identify phases and microstructural...

... temperatures such as 900, 950 and 1000°C. The formation of an interfacial phase has been characterized by X-ray diffraction and scanning electron microscopy. The variations in hardness values were recorded with the variation of sintering temperature, and these have been correlated with the formation...

... marks. * Corresponding author e-mail address : tsrivatsan@uakron.edu 29 05 2012 04 12 2012 ICE Publishing: All rights reserved 2013 alloys material science mechanical properties metals microscopy Recent years have seen noticeable to commendable improvements...

... reserved 2013 * Corresponding author e-mail address : vijayjoseph@karunya.edu composite materials material processing microscopy Figure 4 Optical micrograph of friction stir–processed copper surface composite: (a) transition zone and (b) stir zone...

... author email address: tsrivatsan@yahoo.com 12 04 2012 29 05 2012 ICE Publishing: All rights reserved 2012 applications material structure material properties metals metallic microscopy stress Figure 1. (a) Optical micrograph showing the key microconstituents...