... reinforced plastic samples reached 70% of the strength of samples reinforced with steel sheets. (corresponding author: tahirakgul@subu.edu.tr) 20 09 2021 20 09 2021 ICE Publishing: All rights reserved 2022 mechanical properties strain stress sustainable materials...

... with temperature, temperature distributions of 20, 40, 60, 80 and 100°C were applied. It was found that the radial and tangential stress values calculated at high temperatures were higher than those at low temperatures. It was observed that the absolute tangential stresses were much higher than the radial stresses...

... Workbench software. FEM analyses were performed at 13 bar operating pressure. The results were compared in terms of deformation of the gaskets and von Mises equivalent stress. The most suitable gasket geometry was determined according to the simulation and FEA results. Figure 2 Design parameters...

... author: berkant.dindar@gop.edu.tr) 22 10 2020 23 04 2021 ICE Publishing: All rights reserved 2021 composites stress structural properties Aluminum (Al) alloys are widely used in engineering structures due to their high strength, good corrosion resistance and visual...

...Yasar Kahraman, PhD Although a technologically interesting characteristic of boriding is the production of a hard, wear-resistant layer on the treated steel parts, thermal residual stresses may lead to crack formation in both the iron boride (FeB) layer and the vicinity of the iron boride–diiron...

... with their shear strengths The failure behavior and the mortar resistance under shear stresses of masonry units were investigated without applying any plaster on the surface. This unreinforced masonry specimen for this experimental campaign was defined as the reference test sample. For this purpose, triplet...

...–Hilbert problems according to the methods of self-similar functions, and analytical solutions of the stresses, displacements and dynamic stress intensity factors for the edges of symmetrical mode III interface cracks subjected to moving enhancive loadings, Pt ⁶/x ⁶...

... rights reserved 2019 material processing stress surface characterisation A absorptivity of the surface b_k(T), n_k(T) material constants c specific heat capacity D(t) diffusivity of the carbon atom...

...Xinwu Ma, PhD; Wang Fang, MSc; Wenjuan Zang, BSc The reverse analysis method is presented to determine the flow stress of magnesium alloy sheet AZ31B based on limiting dome height tests. The determination of flow stress is treated as an optimization problem by the reverse analysis technique...

... relaxation tests at the linear viscoelastic segment, and stress-reduced time master curves at different strain levels were established to determine whether the time–temperature superposition principle (TTSP) could be used to assess the non-linear mechanical property of the HTPB propellant. Results showed...

... mathematical modelling stress b constant E_c modulus of elasticity for compression E_T modulus of elasticity for tension EI flexural rigidity of the beam F sum of axial forces h_c...

.... In this study, the temperature and stress distribution in cement concrete base layers in sports venues was investigated. A transient, two-dimensional finite-element model was built to predict the transient temperature distributions at various depths in a plastic runway of cement concrete base using the Ansys...

... stress surface characterisation In recent years, three-dimensional (3D) printing has become a new type of manufacturing technology; it can facilitate the creation of 3D physical objects by piling up materials, thus largely reducing resources and production costs. However, in the application...

... to optimisation. It can be concluded that the influence of LSP on surface roughness is proved to be quite weak according to the simulation results of surface morphology. The influence of different parameters on LSP is discussed based on the residual stress field distribution of the model. The optimal effect can...

... increased by temperature annealing together with stress annealing. After applying a certain stress, the same GMI effect can be obtained with a much lower annealing temperature. In the present paper, it was found that the crystallization of Fe-based sample can reach its best GMI effect with a ratio...

... leakage current, and low mid-gap interface state density as compared to the control device, while DADA Hf_0.2Zr_0.8O₂ has degraded the value of EOT as well as a degraded interface. When devices are subjected to a constant voltage stress in the gate injection mode, DSDS...

... of these two steels revealed features reminiscent of the occurrence of “locally” ductile and brittle failure mechanisms. Over the range of maximum stress and at the two different load ratios, the two steels were cyclically deformed. It was observed that the cyclic fatigue resistance of the candidate steels...